Xteink Setup Guide: App, Firmware Update, Reset & Manual
Short answer
- App: Xteink's companion app is called XTEINK (iOS, Android). It pairs with the reader and sends books and wallpapers.
- Update firmware: connect to 2.4 GHz Wi-Fi in the Sync menu, then go to Sync → System Update → Check for updates.
- Frozen? Charge for 10–15 minutes, then hold Power. If it's still stuck, take out the microSD card and use the reset pinhole.
- Manuals: Xteink publishes official PDF manuals for the X3, X4 Classic, X4 Pro and X4 on its user guide page.
This is the quick-start Xteink leaves out. It covers first setup, the app, updating the stock firmware, and what to do when the reader freezes. It applies to all three current models (the X4 Classic, the X4 Pro and the X3) plus the discontinued original X4. Where a model works differently, we say so.
1. First boot and charging
- Charge it first. Current models charge through a magnetic pogo-pin adapter on the back. Snap it on and plug in a USB-C cable (the X4 Classic box doesn't include a cable). Only the original X4 has a USB-C port.
- Power on with a long press on the power button.
- Leave the microSD card in. It holds your books, and the reader indexes it on first start.
- Learn the buttons. The X4 Classic and X4 Pro have a page-turn button on each side, plus Home and Power. The X4 Pro adds touch (tap the left or right half of the screen). The X3 adds tilt-to-turn, and the Classic has an optional motion page-turn you can switch off in settings.
2. Set up the XTEINK app
The official XTEINK app is optional, but it's the easiest wireless way to send books and wallpapers from a phone. Install it, create an account, then bind your reader from the app and follow the on-screen pairing steps. Once paired, you can transfer EPUB, TXT and XTC files and set a custom wallpaper. There's also a browser tool, XT-Cloud, for importing and converting books.
You don't need the app at all if you prefer the microSD card or Wi-Fi upload. See How to get books on your Xteink for every method.
3. Connect to Wi-Fi and upload books from a browser
- Open Sync → Network Connection and join a 2.4 GHz network. Xteink readers don't support 5 GHz-only networks.
- To upload from a computer, open Sync → Wi-Fi Hotspot (or file transfer). The reader shows an address such as
192.168.3.3. - Open that address in a browser on the same network and upload your files.
The X4 Pro also has an official USB mode that mounts the reader as a drive on your computer. The X3 and X4 Classic don't list USB transfer.
4. How to update Xteink firmware
- Charge the reader above about 50%.
- Connect to 2.4 GHz Wi-Fi (Sync → Network Connection).
- Go to Sync → System Update → Check for updates and install. Some X4 Pro guides describe the path as Settings → Update. Use whichever your menu shows.
- Don't power off or remove the card while it installs.
- After updating, if books are missing or out of order, rebuild the library index: open a book, press OK and choose Index.
Xteink's autumn 2026 firmware for the X4 Classic and X4 Pro, nicknamed "XT Licorice", added TTF font support, a USB transfer mode and reading statistics, according to The eBook Reader. Xteink's user guide page also links a "Firmware Flash" tool for reinstalling stock firmware from a computer.
5. Xteink frozen or not turning on? How to reset it
Xteink doesn't publish official reset timings, so these steps combine the manuals and owner guides such as readme.club. Try them in order:
- Charge for 10–15 minutes. A fully flat E Ink reader can show its last page and look "frozen" when it's actually just out of power. The screen keeps the image with no battery.
- Long-press Power until the reader restarts.
- Remove the microSD card and restart. A corrupted file or a card that fails to index is a common cause of hangs on boot.
- Use the reset pinhole. Press it with a SIM tool, then hold Power for about 3 seconds. On the original X4 the pinhole is on the edge. On the X4 Classic it moved to the top right.
- Reinstall firmware. If it still won't boot, reflash stock firmware with Xteink's Firmware Flash tool, or the CrossPoint web flasher (which can also restore official images).
Book won't open but the reader works? That's usually a file problem rather than a device fault. DRM-protected books, unusual EPUBs and XTC files made for the wrong screen size are the common causes. See XTC file won't open for fixes.
6. Optional: install CrossPoint firmware
Many owners replace the stock software with CrossPoint Reader, free open-source firmware with a better EPUB renderer, custom fonts, sleep screens, Wi-Fi upload, Calibre and KOReader sync. As of v2.0.0 (November 2026), it has builds for the X3 and original X4, the X4 Classic and the X4 Pro. You flash it from crosspointreader.com in Chrome or Edge with a data-capable USB-C cable (through the pogo adapter on current models). The same tool can put official firmware back.
Match the build to your model. The X3 and original X4 use an ESP32-C3 chip; the X4 Classic and X4 Pro use an ESP32-S3. Flashing the wrong image won't work. Unofficial firmware may affect warranty support, so read Xteink's terms for your purchase.
7. Make it yours
- Sleep screens and wallpapers: sizes and formats are in Xteink wallpapers and sleep screens, and our free sleep screen maker exports ready-to-use BMPs.
- Fonts: see custom fonts on Xteink.
- A case and spare charger: see Xteink cases and accessories.
- Calibre users: see Using Calibre with Xteink.
For control over how every page looks on any firmware, convert books to XTC with our EPUB to XTC Converter. You choose the font, margins, spacing and hyphenation, and it has presets for 480×800 (X4 Classic, X4 Pro) and 528×792 (X3).
FAQ
What app does Xteink use?
The official companion app is called XTEINK and is available for iOS and Android. You bind your reader to it, then send books, TXT files and wallpapers wirelessly. The app is optional; microSD and Wi-Fi upload work without it.
How do I update my Xteink firmware?
Connect to a 2.4 GHz Wi-Fi network under Sync → Network Connection, then choose Sync → System Update → Check for updates. Keep the reader charged and don't power it off during the update.
How do I reset a frozen Xteink?
Charge it for 10–15 minutes, then long-press Power until it restarts. If it's still stuck, remove the microSD card and try again, then press the reset pinhole with a SIM tool and hold Power. On the X4 Classic the pinhole is at the top right.
Is there an Xteink manual?
Yes. Xteink publishes PDF user manuals for the X3, X4 Classic, X4 Pro and original X4 on its user guide page at xteink.com/pages/user-guide.
Does Xteink work with 5 GHz Wi-Fi?
No. Xteink readers connect to 2.4 GHz Wi-Fi only. If your router combines both bands under one name, enable a separate 2.4 GHz network for setup.
Can I go back to stock firmware after installing CrossPoint?
Yes. Restore your firmware backup or flash Xteink's official firmware from the CrossPoint web flasher or Xteink's Firmware Flash tool.
Set up? Now make your books look great
Convert DRM-free EPUBs to XTC or XTCH laid out for your exact Xteink screen, with your own fonts and spacing. Offline, one-time $9.99.
Get EPUB to XTC Converter